Can You Repair A Umd
Repair guide : UMD bulldoze door PSP 2000
Level : Very hard Fourth dimension : 60 min Author : Alexandre
155 people accept done this repair successfully ! Why not you?
This guide will explain to you how to replace the UMD bulldoze door on your PSP 2000.
Problems: Cracked or damaged UMD drive door
Some communication before y'all kickoff
Recommended repair kit
Step ane
Earlier proceeding to disassemble the UMD drive door on your PSP 2000, yous have to, for evident safe reasons, turn information technology off.
To do this, concord the power push button for a few seconds then wait for the panel to plow off.
This button is on the bottom right of your PSP 2000.
Step two
Press the button to open up the battery cover, then open the cover.
You tin can then grasp the battery comprehend in lodge to remove information technology completely.
Step iii
Now grasp the bombardment and remove it.
Step 4
At present you have to remove the warranty sticker in your PSP 2000. This means the warranty on your PSP 2000 will probably exist invalidated by Sony after this pace.
Using the tweezers, carefully detach the warranty label that's stuck downwardly underneath the battery placement of your PSP 2000.
Step 5
Use the cross headed screwdriver to unscrew the four screws circled in red in the photo.
These secure the front example on your PSP 2000.
Stride 6
Turn your PSP 2000 and so the bottom edge is facing y'all.
Now unscrew the cross headed screw on this edge. This screw is circled in cherry-red in the photograph.
Step 7
Now turn your PSP 2000 so the top border is facing you.
Unscrew the two cross headed screws on either side of the dock connector. These screws arae circled in ruddy in the photo.
Step 8
Turn your PSP 2000 and so the front is facing upward.
Then grasp the forepart cover of your PSP 2000 and remove information technology carefully.
Information: On some PSP 2000 the front encompass can be a fiddling harder to remove. In this example, don't hesitate to lever information technology upwardly with a nylon spudger around the edges.
Stride 9
Use the nylon spudger to carefully unclip the right side of the Get-go bar.
Step 10
Do the aforementioned for the left side of the START bar in order to unclip information technology entirely.
And then lever upwards the Start bar in order to push button it upward to a xc° bending.
Don't try to remove the Commencement bar yet, it's notwithstanding attached to the motherboard by its connector cablevision.
Step 11
Take the nylon spudger and very carefully lever up the height edge of the screen in lodge to lift it up.
Annotation: Be very careful during this step in order to non damage or crack the screen.
Pace 12
Grasp the LCD screen in society to agree it vertical.
Whilst belongings the screen straight, employ the nylon spudger to unlock the latch on the START bar cables connector.
Footstep 13
Now carefully put the LCD screen back downward.
You lot can now grasp the Showtime bar and remove it carefully.
Footstep 14
Lift the LCD screen of your PSP 2000 again.
Using the nylon spudger, carefully lever up and unlock the latch on the LCD screen effulgence cables' connector.
Footstep xv
Still using the nylon spudger, unlock the connector for the power supply and data cable for the LCD screen.
Step sixteen
Next, carefully grasp the LCD screen by the edges and remove information technology.
Grasp the LCD screen simply by the edges, without touching the LCD display. Fingerprints on the LCD display are very difficult to clean.
Step 17
Now unscrew the cross headed spiral circled in cherry with the cross headed screwdriver.
This secures the trigger push button on your PSP 2000.
Pace eighteen
Utilize the tweezers again to remove the plastic bracket securing the Fifty push button.
Footstep nineteen
Using the tweezers, remove the Fifty trigger from your console.
Step xx
Now utilise the nylon spudger to carefully disconnect the push button button mechanism for the left trigger.
Stride 21
Use a cross headed screwdriver to unscrew the screw circled in crimson in the photo.
This spiral secures the Fifty button cablevision to the example of your PSP 2000.
Stride 22
Unlock the FPC connector for the 50 cable with a nylon spudger.
Step 23
Now use the tweezers to grasp the L cable and its bracket.
Then delicately remove them from the console.
Step 24
Using the tweezers, grasp the buttons on the right (activeness buttons) and remove them.
Step 25
Grasp and carefully remove the metal support bracket for the LCD screen.
Stride 26
Go along to remove the metal shield on the motherboard.
Stride 27
Using the nylon spudger, unlock the FPC connector for the R cable.
Step 28
Utilise the point of the nylon spudger to remove the R cablevision from its connector.
Stride 29
Using the nylon spudger, disconnect the WiFi antenna cable from the motherboard of your PSP 2000.
Step 30
All the same using the nylon spudger, disconnect the power plug connector.
Note: Be very careful during this pace, ensuring yous don't damage the connector!
Footstep 31
Use the nylon spudger to unlock the UMD drive laser lens power supply cable.
Step 32
Then utilise the tweezers to grasp and remove the cable from its placement.
Step 33
Utilize the nylon spudger to unlock the UMD drive motor power supply connector.
Step 34
Use the bespeak of the nylon spudger to remove the UMD drive motor power supply cable from the connector.
Step 35
Using the nylon spudger, carefully lever up the right speaker in guild to unclip it from your PSP 2000.
Step 36
Using the tweezers, grasp and remove the correct speaker in your PSP 2000 from its placement.
Step 37
Grasp the motherboard past the edges and carefully remove it without forcing information technology out of your PSP 2000.
Step 38
Turn your PSP 2000 over so the UMD bulldoze is facing you.
Using the tweezers, grasp the part securing the cover for the UMD bulldoze, then remove information technology. This is a foam part on the right.
Footstep 39
Apply the tweezers to remove the foam part on the left.
Step xl
Unclip the left part of the bracket securing the UMD drive door.
Stride 41
Turn your PSP 2000 over over again.
Then pull out the white plastic subclass for the UMD bulldoze door spring with the tweezers.
Step 42
Still using the tweezers, carefully remove the spring for the UMD bulldoze door.
Step 43
Use the nylon spudger to lever upward the left side of the UMD drive door. This is to release the cover from the hinge on the frame of your PSP 2000.
Step 44
You can now grasp and lift the UMD drive door to remove it.
Step 45
The UMD drive door on your PSP 2000 is at present removed.
Supersede the encompass with a new one if necessary.
Recommended repair kit
Source: https://www.sosav.com/guides/game-consoles/sony/sony-portable/psp-2000/umd-reader-port/
Posted by: smithyouslovis.blogspot.com
0 Response to "Can You Repair A Umd"
Post a Comment